Huashan Replacement Brass Ceramic Disc Stem Cartridge Faucet Valve Quarter Turn 1/2" X 53mm x 12mm spline length 20 teeth(PAIR Hot & Cold)

I was getting tired of our very expensive kitchen faucet dripping about once every 15 to 30 seconds and tried sourcing a replacement valve at two local hardware stores. No luck. I looked up the brand/vendor for the Swiss made KWC faucet and found that the OEM valve a was available from one supplier in the US at the outlandish rip-off price of $66 per valve. I was almost prepared to buy it until I found that shipping was around an additional $75. Yikes! I took careful measurements of my existing valve and compared them with the very detailed drawings on this vendors page to make sure I got the right fit. I got two valves for less than 10% of the shipped price of a single OEM replacement. I only needed one. It arrived in Hawaii in a few days, installed easily in less than 3 minutes. Perfect fit and has a nice solid action feel. No more drips. 100% satisfied!

After shelling out more than $1,200 for a Whitehaus Collection Vintage III Bridge Faucet, Bar Sink Faucet and matching Pot Filler for our Kitchen Remodel in 2012, imagine my surprise to realize that the cartriges in these stunning, high-end faucets were absolute garbage. Once a year at least one cartridge would fail (leak) and need to be replaced. The only place to find these was directly from Whitehaus Collection and they sold them for $60 each! That one heck of an reocurring dividend for them on a $1,200 sale especially when you count the number of times I also had to replace o-rings and nylon washers to prevent leaks elsewhere on the body of the faucets! It was so common that something would fail that I'd buy a spare cartridge or o-ring each time I had to order a replacement from the manufacturer. Frustrated, I made it my quest to find the 3rd party supplier of these cartridges. I tried off and on for years but to no avail. Underterred, I started mapping out the threads, length, splines etc of the OEM cartridge and with every order of a $60 replacement cartridge, I'd search Amazon and other plumbing suppliers and ecommerce platforms to find a lower cost replacement. Finally, last week EUREKA... I got this PAIR of hot and cold all brass ceramic cartridges for $10 with free prime shipping and not only did they fit perfectly but they also work perfectly, no leaks, smooth operation and the water turns off when you turn the handle. Fingers crossed, they will last as long or longer than the ones from the OEM. They worked so well, that I came back and bought 4 more sets - 8 cartridges for less than the price of one from the manufacturer. Now I have in inventory to last me a few years with no fear that they might someday dissapear off of Amazon. Buy these if you have a Whitehaus Collection Vintage III bridge faucet!!! 10 out of 10!

I purchased these to fix a drip on a kitchen sink faucet installed nine years prior. They've been in service for two years and are trouble free. I couldn't find them locally and comparable cartridges were priced two to three times higher. the value and quality are great.

After searching everywhere for a replacement cartridge for the Vigo Zurich VG02007 I found this set. It is a perfect fit for the pot filler. Wish they sold them individually as only need the red "hot" cartridge. The blue "cold" will work but the lever will turn in the opposite direction.

Worked well. Slightly shorter too threaded portion) than the one it replaced- was able to raise faucet body itself so that the shortness was compensated for. Measure carefully before ordering to be sure of a easy job.

These were hard to find at a reasonable price from anywhere, far as I can tell. These have a top thread that the easy-to-find valves didn't have; my faucets have decorative polished-brass "hoods" that screw on between the faucet body and the knobs. They are solid, appear very well made, and work just great. One issue (NOT the supplier's fault!) is that my original valve stems had a 16-tooth spine, while these have 20. I was able to find a pair of decent-enough looking acrylic universal knobs (with metal inserts) at my local big-box hardware store while I figure out a way to modify the original polished solid-brass knobs, by drilling them out and using setscrews. ... Update: using a drill press, drilled out the holes in the original brass knobs so the splines were no problem, and drilled 2 holes at 90 degrees to each other in the side of each knob, tapped to 8-32 and inserted setscrews to fix each knob to its valve stem. Problem solved. Be careful when shopping for these; there are some that look quite the same, but some don't have the top thread, and some have a different distance from the shoulder to the top thread etc. Five stars, these are really good so far. No leaks either.

OK, first let me say that I had two Aquasource (#289839) 8" spread lavatory faucets, so before I ordered these valves, to fix the old stuck cold side on the faucet at my property, I just swapped the entire cold valve assembly and handle from the extra faucet I had, and then I bought these valves to replace the just pulled cold assembly. I mention this because I do not have a need for my 2nd faucet right now and hence cannot say whether my new valve just purchased will be leak free. However, I was compelled to leave my review now because I put the new cold valve in the old faucet cold assembly I pulled and the fit was PERFECT. All the threads were in great shape, the handle fit perfectly on the 20 count threaded valve stem top, and the valve screwed into my old assembly beautifully. I put that all back in the box of my extra faucet box, so when needed, I have basically a brand new faucet ready to go, PLUS the extra HOT valve in the 2 set purchase that I did not need currently, all for $10, properly wrapped for protection and promptly shipped! I could not be happier to repair a quality old faucet like this with these quality replacement valves so economically! Note that I gave 4 stars in the "Instruction Quality" section, only because there were NO instructions, BUT NONE ARE NEEDED. Anyone who cannot clearly and easily see how these new valves go into the faucet's valve and handle assemblies has no business ordering nor using these, because it is such a basic fix.

couldn't find faucet handles?