Premium Retractor with Snap

We love this retractor function to have quick access to the camera when we're underwater. The weight is a little heavy but when you are underwater, there's not much of a difference.

I saw another reviewer (Robert M) who did a similar install - I wanted to offer mine: Up front: I started with the multi-mount ($22) accessory that is meant to go with the Hydros Pro (but I assume you could do something similar with whatever BC you have) 1. ScubaPro Premium Retractor: I unscrewed the 4x screws that kept the overall housing together (be careful) 1a. Take out the plastic "Stop Button", (I had no use for this feature) leaving you with perfectly aligned holes. 2. I took out the bolt snap that came with it (this drastically reduces the overall size of the retractor)...immediately re-install the bolts to keep everything tight. 3. I purchsed the same bolts (but longer) from Home Depot (Stainless) 4. I hack-sawed about 1/8" from the purchased tipped screw (to keep the depth and prevent any sharp edges) 5. I kept the plastic washer, and mounted the retractor, using the "created holes" from the vacant "stop button" and into the "multi-mount". --- --- --- 6. I then unscrewed the existing 2x phillips head black screws from the other side, and replaced them with 2x eyelet screws (also from Home depot (stainless), same pattern... 7. I fished a zip-tie through these 2x eyelets, arount the multi-mount, and secured everything. Permanent mount, streamlined, and clean! You may notice I replaced the split ring with a black solid ring...this is just my OCD, and not needed. By all means, have at it! I hope this helps!

This scubapro retractor is made of high quality components and uses a spring coil as the retractor mechanism. I modified mine to use on my scubapro hydros pro.... The metal hardware it came with were high quality as well. *NOTE* The orginal locking/unlocking slide button did get in the way and seemed to be more of a hassle for it would lock/unlock on it's own... so I just removed it.

The pro and con are the same there is a line lock, but the release is small

This scubapro gear keeper gets unwarranted praise. On the 5th dive the plastic that covers the cable started tearing apart. See picture. This causes the retract mechanism to bind and block. Total fail. I cannot believe this group of pro put this out there and they're testing did not reveal this clear design flaw. Then, the little button that locks the gear retract open or closed is constantly locking open or locking closed on its own. So you go to pull out your camera or flashlight or whatever you have it attached to and it's locked closed all on its own preventing you from pulling your device out. You have to reach up fiddle with the button to unlock it, stretch your arm out to light your subject or film your subject, and then it often locks again so your device is just hanging there, not retracting. I'm going to tape mine permanently shut so it doesn't lock open or closed. I am normally a fan of scuba pro products but this one is a complete fail. It's easily twice the price of other devices. I strongly recommend you do not invest the money on this POS. Just buy some cheap ones and replace them every couple of years.

The plastic wire liner has started peeling off, exposing the wire underneath and I’m worried about fraying. Good enough for now though and manages my camera case adequately.

Lasts longer than other brands I have. I have yet to break one of these. It's more expensive, but you get what you pay for.

Secured a G2C dive computer to my BCD shoulder strap D-ring. Every time I checked depth/air/etc. it secured the G2C back into position and held it right in place. Quality!

Sehr practisch durch Schluesselring und Karabienerhaken zum anbringen von Equipment

Très pratique pour se libérer une main sous l’eau

Article solide et pratique. Utilisé avec une lampe de plongée assez lourde, le rétracteur fonctionne bien.

validissimo

I used it to attach a camera to my BCD. It's fairly sizeable but that makes it robust and easy to locate and use. It's not too big but I wouldn't want it any larger. All the components are of high quality. Mechanism is smooth and seems durable. If flying, ensure you stow it in your hold baggage. I had issues with security when it was in my handbaggage.