APDOE Egg Incubators for Hatching Eggs, Temperature and Humidity Control, Automatic Egg Turning, Egg Candler, External Water Bottle, Air Vent, for Chicken, Duck & Quail Eggs, 12 Eggs

I agree with all the other positive reviews so I'll keep this one short. This is a great incubator (our first) and it has performed flawlessly. We are due our first hatchlings in a day or two. I read at least one reviewer who stated that the humidity fluctuates significantly and is difficult to control. We found that the humidity fluctuates in sync with ambient humidity levels which has nothing to do with the incubator itself. Our incubator's humidity shot up quite a few percentage points during a rainy spell that we had and then dropped back down afterward. The instructions offer effective solutions for adjusting the humidity. We are very happy with this incubator in all respects.

Holds temp and humidity sufficiently but you do need to run it a bit to stabilize like the directions say. The candling light on top is not strong enough to see thru brown or darker colored shells. You'll need a separate and stronger light for those. Very easy to use, set up, and clean. The directions are detailed and it's a very good value for the price. Have 2 chicks hatched no problems and 4 more eggs pipping right now. So if you have fertile eggs then this incubator is very good, very easy to use and the price is very good value. The insert with instructions includes all you need to know if you're hatching eggs for the first time. Overall very happy with my purchase. Additional note: the incubator did run a little warm, even though it said it was 100 F, it was a slightly warmer so recommend checking with a separate thermometer inside before setting eggs. There have been some studies that show a slightly higher mortality in male chicken eggs when the temp runs high and a higher mortality in female chicken eggs when the temp runs low, but also lower hatch rate overall if the temps are off. That seems to hold true as I got 75% female to 25% male out of my hatch. I didn't realize this machine I got runs a little hot and didn't check the temps independent from the thermometer on the machine before setting eggs, my mistake. The eggs also hatched 2 days earlier because it ran warmer and I only had 6 eggs out of 12 that hatched. Out of the 12, 6 hatched, 3 were very well developed but died before hatch (probably males), one was barely developed and 2 never developed. If you have a rooster and hens and have eggs to spare this could possibly be a way to get more hens and less roosters but it was only one study I read and only one hatch experience so far by me so try this at your own risk.

Awesome incubator! Did the job! Easy to work and is very quiet. My only complaint is how hard the lid is to close sometimes.

We incubated 18 eggs, and we now have 18 chicks! Im so impressed with how well this worked! Very easy to use. We have high humidity where I live so we had to put a tiny crack in the lid for the whole incubation time.

Update: 6 healthy chicks hatched! At first I thought it was defective since it didn't turn the eggs every hour, but I finally saw it roll them! Eggs only need to be turned 4-6 times a day, so if its not every hour I'm fine with that. I set a second thermometer in there because this incubator doesn't have a decimal for 99.5 degrees. I found that the 100 is actually 100.5 so setting the temp to 99 actually equaled 99.5, perfect for hatching. The directions are perfect, follow them and don't deviate. Only I took my turner out the first 3 days so I could put the eggs pointy side down in little cups to let the air sacks develop at the top of the egg, then I put the turner back in and laid them pointy side pointing towards the middle. My only complaint and the reason for 4 stars is that the humidity keeps dropping below 50%, so I keep having to add tiny bits of water into port B and so it fluctuates between 45%-55%. You should also know, this is a TINY incubator, but it fits on a dresser nicely. My eggs are on day 5 in there. I'll try and remember to update when they hatch.

This product can not score anything higher than a one due to a failure that could have killed my pipping ducklings. I will talk about what the product can do, what we used it for, and everything else, but a random failure like this is inexcusable. So please when you read this review, keep what I say in mind. But before I even begin: ALWAYS, ALWAYS, ALWAYS have a backup incubator! You will see why. Also, this will be a long review, but it can't be helped. I don't want anything bad to happen to anyone else's eggs. If it means I have to be longwinded, so be it. Please be careful. Alright. Currently, we had a batch of about 16 duck eggs, at various weeks and levels of readiness. Because of this, we have two incubators: One set up for embryo development and turning (the nurture right 360 incubator), and this one, for hatching. We went with the 12 egg capacity one, which comes in a pretty small profile and nestled quite nicely next to our main unit. Since this incubator was primarily for hatching, we didn't use the turning feature since you do not turn eggs in lockdown and leave them be. Thus, I can't critique the turner since it was not utilized. The main features that were utilized were the water reservoir bottles, the heater, and we did test the Candler. The vents...well, they were left open, kind of hard to review a vent. It does what a vent does. The Candler was fine. Did well. If you own a nurture right 360 incubator, you will notice some pretty strong similarities between this product and that one. You have two little trays on the outside of the unit that you feed water into, and it effectively trickles into these recessed trays at the base, and the heating element of the incubator causes the water at the bottom to heat up and create a humid environment. The difference is that although both incubators have this feature, this one opts to create a closed reservoir system using bottles and a finnicky plastic "lid" that goes over the hole of the tray and trickles the water in that way. This was a neat feature that I wished the other incubator had because it is much easier in my opinion to remove a bottle and adjust as necessary (in theory) then slowly injecting water into the tray via syringe. I say in theory, because in a situation where you have to remove a bottle either to refill or to simply remove to alter the humidity environment, you have to effectively wrestle it out of the tray, which will jostle the eggs inside. The plastic lids just end up being TOO snug. ....but that's it. That's all the nice things I can say about it. The adjustable water bottle feature that is neat... ...but this product failed at a very critical moment, and now we could potentially lose a duckling or two over it, and possibly over seven embryos are going to be impacted as well. I am trying not to be so upset over it, but here's what happened. Over all, we had put at least seven eggs through the hatching process in this incubator. The very first egg hatched pretty much text book perfect. The zip line was perfect, the membrane was moist, and the temperature and humidity just seemed to be highly accurate to what the readings said. The egg that we hatched first was a lone survivor from her week, so she would have hatched with others but life had different plans. So fast forward to now, we had six eggs from the same week all scheduled for lock down. We put them in there, and noticed that the 12 egg capacity of the unit must be referring to naturally smaller eggs, not average sized duck eggs, so it was a bit snug in there and this is WITHOUT the turner. That was fine, and in any other incubator the more that's in there, the more stable things tend to be. But that was NOT the case with this one. So, right from the jump, the textbook duck hatching process did not happen as cleanly for these. They all had some manner of issue with their hatch save for one. The first two to hatch from the six were more allocated towards the outer right side of the incubator, they hatched together, but they weren't able to get a clean zip. They came out ok, reallocated to the brooder, no problems. The next one to hatch, was actually hatching earlier than their siblings by an entire day. This usually indicates a fluctuation from the temperature (which was not the case) or they simply were further along, much more likely the case. The duckling was not shrink wrapped, but you could tell with the coloration of the inner egg shell something was off. It was not behaving as it should with 70% humidity. It was acting like it was on the low end of 60%. But that shouldn't be since the inner humidity would be stable with both water bottles being used. I ended up removing one, and tested the inner humidity through another tool and noticed with OUT the second bottle, it was climbing to the proper humidity level (and with both, the humidity was off about 5%). The duckling hatched, clean bill of health, no harm no foul. Into the brooder. Three eggs left. This is where the nonsense reaches a critical point. So this whole time, one of the eggs was positioned on the opposite side of the brooder where the others were tending to hatch. They hadn't pipped yet, while their siblings were. That's not too weird on its own, but it was of note, because once the three other ducklings hatched and moved on, the three remaining eggs were left over, but the temperature was struggling to maintain it's programmed point, swinging a degree off wildly but not in a normal manner. ON TOP OF THIS. ON TOP. OF THIS. One of the three started hatching, but was showing signs of the membrane being too tough to get out of, again. So I checked the humidity, and it wasn't reading at 75%, it was reading at 62%. That's a 13% swing in the opposite direction. We had to intervene to get the duckling out of the rest of it's shell. Clean bill of health, into the brooder. Two eggs left. Remember, all same week, one of the eggs on the opposite end wasn't showing signs of pip, despite the others. Well I was getting really exhausted from how inconsistent it was being, and was starting to concoct something else to try but I wanted them to at least get through this hatch since it would be too risky this late to switch them over. Well, the egg on the far end finally did pip, in the wrong direction. The pointed end. When this happens, you usually have to intervene at this point since something clearly went wrong and ducklings from wrong end pips don't tend to have great success rates on self hatch. It wasn't just this though. As we noticed this, the entire unit. THE ENTIRE UNIT. completely shorts out. Dies. It fricking dies. Heater is gone. Humidity is whatever the hell is going on in there. So we had to immediately relocate the two remaining eggs into the embryo one, remove the turner, all this stuff. On top of this, now we have to triage and try to save the wrong pipped duckling only to learn the poor baby is shrink wrapped, which is a tell tale sign of inadequate humidity. Poor darling is rough, but breathing, alive. Yolk not absorbed, it's a whole thing. We can't even process that this incubator just absolutely shorted out and broke for no discernable reason. The second egg seems to be ok for now, but because of this emergency, and the FAILURE of this unit, we had to adjust everything in the embryo incubator to accommodate these two, so the embryos are not in ideal conditions as a result of this. So not only could I lose this duckling we are trying to save from this unit's absolutely deplorable humidity conditions, we could lose embryos too. This is unacceptable. This is completely, and utterly unacceptable. I understand freak things can happen, I am willing to give the benefit of the doubt, but it just died for no reason. It was struggling to even maintain humidity despite ideal circumstances that the unit even calls for (use both bottles for higher humidity, only for that to NOT be true) and I could lose some ducklings over this. So forgive me if I seem a bit heated, but seriously, this is why you need to have two incubators. If I lose some embryos, so be it, but these two ducks have a chance now because of the backup. As for this unit? Does it work? I hatched some ducklings in it. It "can" work, but you really have to baby this thing and it isn't something I don't think most people could dedicate to doing since it fluctuates so wildly. Especially if you work a job outside of the home. MAYBE it's just my unit since it just died, but we are talking about living creatures here that require so much particular settings to work as described, and this failed the test in a critical way. Yes, the nurture right incubator is pricier. But it WORKS. IT WORKS AS DESCRIBED. I would highly encourage you to consider paying the extra, or if you are going to buy one of these cheap incubators you need to make sure you have a backup. That is all. 1 stars. This product failed and my ducklings almost died as a result. I do not recommend.

I purchased this incubator with the intention on hatching my own store purchased fertile eggs (instead of buying chicks) and rasing chickens for the sole purpose of having our own fresh eggs. I actually bought my fertile eggs from a local grocery store, which is crazy lol. (Make sure if you're planning on doing the same, you make sure the eggs are fertile and not the regular everyday store bought eggs) I wanted to go through the whole process of the whole egg experience, which has been an amazing little journey. I have enjoyed every step of this process and am excited that I have 6 more days until hatching day! I started with 10 and now have 3. In no way is that the fault of anyone (me, the incubator etc.) This is just life and what can happen during the incubation process. The incubator keeps at the temperature that you set it, so this part was great. The humidity level was a little more of a challenge for me. I base this on the temperature of my home, the location I have the incubator (my kitchen counter) as well being new to this whole thing. Towards these last days I've finally managed to keep the humidity level within a certain range after some trial and error. The Styrofoam insert (don't throw that way) is definitely a life saver in helping keep the humidity level set at a steady temp for a great portion of the day. At night time, I wrap a towel around it as well since it gets so cold at night. The incubator also has an automatic egg Turner (which you need for most of the 21 days). I've seen some incubators that require you to manually turn them and for being my first time, I wanted it to be one less step I would have to do (or remember to do) The incubator is very easy to use, It is nearly silent and it's definitely great quality for a beginner backyard breeder like me. The incubator itself is not cheaply made and seems to me to be very durable for the purposes of hatching eggs. I have had no issues with this at all. It holds 12 eggs, which I recommend you start with 10-12 as a beginner, I'm glad I did. I will give an update (hopefully as a chick mama) as to how it help up after the chicks hatched inside!

This was my very first incubato. I recommend this incubator for the first time egg hatcher. It's easy to use and easy to clean. I liked the temperature and humidity display feature. I also liked the external water reservoir. It came with instructions that were easy to follow. I did not care for the candling light. It was not bright enough and I used a flashlight with a toilet paper tube to candle my eggs. For a beginner this is affordable, easy to use, and easy to clean.

This is perfect for what I want it for. Not hatched anything in it yet. Eggs will be going in this week. It was super easy to set up using the instructions and even came with a brilliant hatching guide, telling you everything you needed to know. I was especially delighted with the candling torch and spray bottle that was included. Looking forward to seeing the results!

Works perfectly!

Easy to setup and love that it easy to control temperature and humidity. Great for small setup or starter hatching. Also unlike others we have had the instructions and very easy to follow and comes with a handy egg guide.

Stooped working after 16 days, and I lost all but 3 eggs. Up until that point I was relatively impressed. The humidity is sooo high and that is an issue. Cheap. Save up and buy a proper one.

Well, it’s hatch day. So far 6/12 have hatched and we still have time left on the clock. I call that a success. The egg turner worked just fine. I was worried after reading reviews from this and other incubators that the turner would stop working or that it wouldn’t hold the right heat/humidity. I did not buy any additional humidity or temperature readers, I relied entirely on the system. I set it to 100, filled the bottles as instructed (bottle 1 only until day 18, then both) and we have chicks! My only concern is that there really isn’t much space for the chicks to move around but they’re only in there for up to 24 hours so It’s not a huge issue. I’m impressed for the price. I assume you can update reviews, and so long as I can, I’ll update when/if it ever breaks on me (or if more chicks hatch) but for now, the first hatch is a success!