Genmitsu 30pcs PCB Drill Bits Set, 0.1mm-3.0mm, 1/8" Shank Spiral Flute CNC Router Bits for Print Circuit Board Jewelry CNC Engraving, PD30A

Below you'll be able to read my old review. But let me tell you this company reached out right away and without asking me any questions basically said hi here's a set of are slightly more expensive bits would you like a set and they sent them to me no problem whatsoever it's 10 bits and these are hardened differently bits pretty sure I got them pretty quickly and immediately sort of testing them and when you if you read the old review you'll understand how I test my bits but because I wanted to see how good these were I push them four times tougher on the first cut with every one of those bits I pushed. I can say not one bit broke not one bit chipped not one bit even lost a little bit of color and yes I'm still operating at slow speeds to test them but it's now been a couple of weeks I've done a few things and a couple of those bits become my go-to for dealing with specific speeds that are a little bit higher than I might normally like but I'm using all the bits now and I should say that aside from the original bits that broke in which again if you read the old review you'll you'll see I haven't had any other bits from this company break just outstanding. Old review Used with feed rate of 50mm (super slow on my CnC) and right away to bits broke as spindle spun up to speed and started first cut. No other bits either bigger or smaller have broken since, but obviously some flaws in manufacturing of these bits.

I do a lot of detailed modeling. From time to time I need a really small drill bit. This set includes some extremely small sizes. The very smallest one is so small that it breaks very easily, but given how small it is, I really don't see any way around that. These really come in handy, and if I do end up breaking a few of them, I'd happily buy another set.

I love these for a whole lot of reasons. They are very sharp, and cut plastic easily. They are inexpensive, and come in many sizes. They all have the same size shank, so I can easily swap them through my pin vice without having to change adapters. The bad? They are very brittle, a consequence of the hardness that makes them sharp. The bits don't stand up well to drops or getting bound up in media. I have snapped some drilling into white metal miniatures, but they are not really made for that, either. If you are a model builder or mini painter I consider these a must have.

I use these drill bits to use on popsicle stick craft! it dose bore a perfect clean hole, but with a tiny movement you can break the tip easily, so I decided not to re order since its made of some cheap material!

I have used these bits with my pin vise from Stedi. These fit in that drill well and cut through without any issues. I am very happy with the quality, the case they come in and the variety of sizes.

These drill bits work very well and the measurements are spot on. The shank on all of them are exactly 0.125” (1/8”). And the diameter of the drilling ends were all exact, according to my non-Mitutoyo calipers at least. These are much better used in a drill press of some kind because any sideways force on the smaller sized ones and they will snap. These are tungsten carbide so they are very hard and not flexible at all. I use them in a Dremel tool with the Dremel Drill Press and it works great! I think the Dremel Drill Press/Work Station thing is your best bet if you don’t already have a drill press because it’s only like $40 at the time of writing this review, and I would imagine most people already have some kind of Dremel tool if you’re looking to buy these mini drill bits. I would definitely recommend these mini drill bits to anyone needing to make very small and precise holes.

Bits are very sharp.

I got a set of PCB drills included with a pin vise I bought earlier this year, and overall these have come to replace my standard steel drill bits for most model work. For someone who primarily works with plastic, specifically polystyrene, these things cut through it like it's barely even there! A word of warning, especially for those of you who have unsteady hands; these bits are extremely brittle, especially when going below 1mm, but that does mean that the material is extremely hard and likely keeps an edge much better than standard bits would if you don't snap them.

Sehr präzise verarbeitet

Sadece baskı devre çıkartmak için ideal. Herşey için geçerli değildir.

Sharp. I would imagine the 0.1mm will have little or any practical use, unless your drill is zero run-out. The. 0.3mm works fine on mine through 0.5mm brass and 2mm styrene. As a result i am confident the 0.3mm bits and larger will be fine. I have used a few of the larger bits and they are sharp. Just go easy on the smaller bits. They will snap if you apply to much force.

Llegaron justo a tiempo para cumplir con un compromiso. Excelente calidad.

Très bon produit