Duck Brand Indoor 10-Window Shrink Film Insulator Kit, 62-Inch x 420-Inch, 286216

I haven’t had the need to use plastic over windows in awhile. The kits used to come with folded sheets of plastic. This kit actually comes with a roll of plastic. It is so much easier! You start at the top corner and roll it across, then just unfold it down the window. It’s so much easier to maneuver. It has made such a difference in room temp, it’s crazy. My living room was actually at 49, with this plastic up it fluctuates between 68-70 now which is perfect. I’m planning on leaving it up for summer to keep the heat out and lower my a/c costs! This is a great kit, easy to use and works great. They also give you plenty of tape which is very sticky and the plastic is strong and very clear also.

I highly recommend you read the entire directions, and also the other reviews. By reading the very helpful reviews I was able to learn from people who have done this before. It was so worth the time. Speaking of time... that's really the main thing you want to dedicate to this cause - time. If you rush it, it will be unpleasant and not work well. Get your hairdryer ahead of time. Clean and dry the areas to be sealed. If you are doing an old-fashioned door with a checkered=pattern window, like me... Measure/cut to leave enough extra to seal over the grille [cross pieces on the glass]. I just covered my windows on the front and back door that have the glass checker-board panes. I had to cut the tape into 12 pieces. With this type of application the tape had to go on the glass instead of the sill, because the sill is about 50 years old and if I rip off the paint, there is gonna be hell to pay. No worries. It worked on the glass and the draft stopped immediately. There is an issue I can see, and it was mentioned by other reviewers... You may need to use more tape than provided because in some cases the tape gets touched and loses it's stickiness before you are ready to seal the plastic. No worries, just put another piece of tape and don't touch, put that plastic on fast and don't get too many finger-prints on everything as you try to size it. Fingerprint grease is obviously a glue destroyer. For that it's best to do one section of tape at a time. I've done four windows [counting the two doors as one window] so far and still have plenty of tape left. For best adherence, use the dryer to warm the surface you are applying the tape to, especially if it's glass. Then use the dryer to warm up the tape just before you press the plastic onto it, but not too much or it will dry out. The good thing is that this isn't like saran wrap - if the plastic folds on itself it doesn't stick - hence the tape. I also covered 3 regular, modern windows where I could put the tape directly on the clean sill. Worked great, piece of cake. As far as how much of this stuff there is... definitely enough for 5 windows. In my case I've used scraps on the back door - piecing two remnants from the other windows onto this one, since it's rarely viewed it doesn't need to be perfect. It turned out pretty good and that means you can make at least six window covers if you are willing to be creative. One more thing if you do have very leaky windows like these old doors I'm talking about, you may see what I see... that is condensation pooling at the bottom of the plastic which is pulling the plastic away from the glass in those sections. The way I see it... That is condensation that would be in my house, I'm glad that cold water is in the plastic and not in my air. However that does mean that in order to keep the doors from getting more rickety than they already are I have to sop that water up from time to time... and perhaps replace the tape every so often. No worries. The main thing is my heater goes on about half as much as before. I haven't got an electric bill since installing, but I don't think it's rocket science - that's got to translate to savings worth more than the $8 this kit costs. I will never go a winter without it again. Even if there was no cost savings, not having an uncomfortably drafty house is priceless.

This window insulation kit definitely helps keep drafts out and rooms warmer, but it takes some patience to get it right. The film is clear and fits nicely over the windows, and once sealed, it makes a noticeable difference in keeping out the cold. The tricky part is applying heat. You have to be really careful with the blow dryer, I accidentally ripped through a few pieces while trying to shrink the film. The plastic tightens up nicely when done correctly, but it doesn’t take much heat to damage it, so go slow and keep the dryer moving. Once installed, it looks clean and holds up through the season without peeling off. It’s a good affordable option for older windows, just be gentle during setup.

I bought the Duck Brand Indoor Shrink Film Kit because I really didn’t want to take my window AC unit out for the winter, and this has worked perfectly. Once applied, the film creates a tight seal and keeps cold air from leaking in, which makes a noticeable difference in the room temperature. The kit is easy to install — just follow the steps, pull the film tight, and use a hair dryer to shrink it. Even with the AC still in the window, the plastic tightened up smooth and clear. It also feels durable enough to last the entire season. If you’re like me and prefer to leave your AC in year-round, this is an affordable way to block drafts and keep your room warm. It does exactly what it’s supposed to do.

I have used Frost King film for decades. Although it never split, the film was extremely thin. The Duck Brand here, has noticeably thicker film, but far more importantly, the tape sticks to wood and aluminum FAR better than the other brand. It has shrunk tight as a drum, is invisible, and looks great! Costing less than the Frost King makes it a great value. The only negative I found has been praised by others. This kit, 62-inch x 210-inch, comes on a roll. For me, this makes installation more difficult with the roll remains attached. Had I cut the total width first, it would have been a non-issue, I'm sure, but I wanted to ensure I did not cut too short and ruin the roll for my use. I have attached photos of my bay window installation.

It works. BUT. Follow these pro tips for best results: 1.) lay the 2 sided tape. If you go ALL the way around your window in one fell swoop, use a razor blade and score the window corners. Every time there is a 90 degree angle, score this with the razor. The reason is this is an area of weakness, and if it is going to pull off the tape, this will be the first place because there's usually a bend in the tape here. Scoring the tape will prevent this. 2.) While using a blow dryer DOES tighten the plastic, and make it wrinkle free.... forget this step. It's nice for about 3 weeks, but once it gets cold, the plastic tightens more and pulls off in some places. Leave it wrinkly if you're putting these in to keep out cold. 3.) After you lay the tape and have your MEASURED section ready (give yourself 2-4 inches BEYOND you measured, put the plastic up 1" INSIDE the tape. This gives you room to move on the other sides while you put it up, and if you do decide to not listen to me in #2 above, it gives some play in getting it set the first time. Even without using a blow dryer to tighten, leaving a little play keeps strain of the double-sided tape, and keeps you from putting these up again in the winter. My windows suck and I can see the plastic move at times with extreme wind... but now with these up, my furnace can actually keep up, whereas it couldn't last winter. Last tip, don't get the Amazon Easy package, get the name brand (here on amazon too). You're just paying $3 more for a brown cardboard box rather than a duck brand cardboard box... ***update 11/30/18*** These are still good, and working well FOR THE WINDOWS I DID NOT TIGHTEN WITH A BLOW DRYER. I've had to re-tape almost every other window that I used a blow dryer on.... as it gets colder, the plastic tightens more and pulls off the sides in places Never mind using the blow dryer to give the crystal clear effect. If you are putting these o. to keep out the cold, just put them up with a little slack and you'll be fine.

I love this stuff! It works perfectly for drafty windows - Like in apartments. Should also keep out bugs, dirt, and perhaps a light sound barrier. Installation is beyond simple. Anyone can do this, and alone. There is plenty of room for error. As it happens, I had perfect application on four 3x5 windows. Flawless. But, I want to talk about something that I've noticed a few others mention that I was curious about myself. (I got on here hoping to find an answer, and I didn't. So I'm going to try to answer it) The first day after installation of these, I noticed sound coming from them. It wasn't from *wind* like some people assume. I think it was a mix of static and tension, (and maybe sunlight?) Though, I heard it at night too. The sound - slow, soft crinkling of a potato chip bag.. Usually every 20 seconds or so. It's the time that leaves me to believe it's some form of static discharge. This went on for two days before I decided it wasn't 'settling' and I started to think of what was causing it. Well, if this were permanent, you can bet I wouldn't be giving this product 5 stars. So here's how I fixed it. Remember how I said I had a flawless application, but this product leaves room for error? (if you skimmed ahead, that's what you get for being impatient). Well, my application was too perfect. It was as tight as a drum, stretched all across each side perfectly. I had no problem removing an entire side at a time and repositioning it so it was half an inch closer to the window (loosening the fit). I didn't do this on ALL 4 sides, just two. After doing this, the sound was gone! Bam! It's still pretty tight, but nowhere like it was before. It still tight enough to where you can't see it unless you have a lamp in the reflection. Otherwise it's invisible. I'm not sure why or what combination of things caused the sound, but after repositioning it to be ever so slightly looser, all is golden! So my advice, Don't get it drum tight the first time around... And if you do, and experience this noise, just loosen a side or two and it should go away. To apply, I put tape on all 4 sides, then cut the proximal size of plastic, started at the top, and worked my way to the bottom. I didn't have any issues, but the tape is strong, sticky and forgiving. It sticks great to my paint, without removing it (the paint) , and can be restuck many many times as far as I can tell. I did it alone, and you probably can too. Two people would make it easier, but it isn't mandatory. Having a sharp pair of scissors comes in handy. To trim the excess, I didn't trim, but glided the scissors around to leave as clean of an edge as possible. I also didn't have a hairdryer, but I did have a space heater which worked perfectly, Probably better than a hairdryer. It came with two rolls of film. I did 4 windows and have enough left over from the first roll for one more window, and haven't touched the second roll. (Each roll should get you 5 windows, and I'm on track to get just that). I also have more than enough tape left over and have begun to use it for home projects. It's super strong, invisible, thin, and removable. I love it on it's own and would pay 10$ just for that. ****and if you want to get creative... Consider attaching a neodymium magnet to your blind controller in a fashion that could allow you to open and close them as desired, if you so wished! I haven't tried this but I know it would work with some creativity (perhaps super gluing a flat magnet to the base of the spinny thing (attaching it so the N/S polarity is horizontal/perpendicular to the thingy) .. So that you can manipulate it by rotating an equally strong magnet near it (while keeping them apart of course - using your hand as a barrier). If you've played with high powered magnets before, you'll understand how this could/should work. an interesting thought to fix the fact that you can't control your blinds once the film is on) Similar thoughts apply to attaching a magnet to the draw cords (though, they may be too heavy for such ambitious ideas) But adding a weight to the draw string could be a way to counter that. Who knows! I have one more window to do, and I will test this out myself and update with whatever results I have.. Even if they are just awful.

This stuff works as easy and as good as it’s ever has I’ve used it for years very simple to install tighten up with a hairdryer window drafts are gone

This is my first time using something like this but this window sealing kit has been great at sealing out the cold from our house! We have an older 70's house that still has the original windows (single-double pane, no insulation). Which is a killer on our heating bill here in Canada until we can switch out all the windows for newer ones. This sealing kit was super easy to install and is barely noticeable (the only noticeable part being on the window frame if you squint). Drastically could feel and see the difference it made to sealing in our heat! Even going as far as keeping our house from overheating too badly from the sun during hotter temperatures. Overall, would recommend!

Este producto sirve para las corrientes de aire, no para el frío intenso. Te ayuda a que no haya una corriente en el cuarto que pasa de una ventana a otra cuando este cerrada, bloquea las corrientes, pero no el frío intenso ya que requiere de aislamientos especiales y con un costo mayor. Debemos entender para que sirve este producto. A mi me funciono.

This shrink film kit does an excellent job of sealing out cold air, making a noticeable difference in my basement—it’s now much more comfortable to stay in! The installation was straightforward, and the film shrinks nicely for a clear, tight seal. The only downside is that the kit comes with more film and tape than I actually need. It would be great if there were smaller size options. However, the extra materials could be useful for future use or larger projects. Overall, a great product for improving insulation and keeping the cold out!

No complaints with the installation, some of my windows are sliding sash windows so it was a bit fiddly to install but that's not the fault of the product. Pretty forgiving of bad workmanship as a blow with the hairdryer takes out the creases and gives a great finish. Definitely notice the difference in terms of insulation and sound proofing. Worth doing if you can't fit double glazing for any reason.

Easy to use very effective keeps room warm also helps with road noise