ArmorSuit 6 Pack Screen Protector for Apple Watch 38mm Series 3/2/1 Anti-Bubble HD Clear MilitaryShield Film - Made in USA

I'm a little surprised that this item has as many low 1, 2 & 3 star reviews as it does, but I think the product is fantastic so I guess I'm biased. Installation was easy, not a single problem encountered, though I will say, WATCH THE INSTALLATION VIDEO. If you've never installed this type of wet install screen guard. I have done this on iPhones, many times, but I still watched it. The main things to remember: 1) make sure your hands are clean. 2) the area you use to install it in, make sure it's not dusty. 3) have paper towels (viva works well it bounty, less linty bits coming off) along with the microfiber towel when you start. 4) when you start, start by spraying the back of the shield w/ the included solution. If you want, since there are two shields to a sheet, cut it in half & put the other shield away. Then spray the non adhesive back, then your fingers. 5) carefully peel off the shield from its backing, if you sprayed too much solution, use your towel to get off the excess by letting it drip to the edges. Don't try to wipe it off! 6) let the shield adhesive side down on the screen of a powered down device, moving it around until it's where it needs to be. (Don't panic, it will slide around a lot, if solution comes to the edges, use your towel to absorb it.) 7) when you have it where you want, use the squeegee to work out air bubbles, keep your towel nearby for excess liquid. And be aware the shield WILL MOVE ABOUT when you do this, just shift it back in place. Try holding it in place while you squeegee. 8) once you're satisfied that the air bubbles are dealt with & the shield in place, you can leave it to dry a bit, 15 or so minutes until the edges get sticky & you can press them down. OR, you can employ a hair dryer & speed up the process. It takes a bit, hold the heat to the shield a little & as you do this, try to get the corners to adhere to the edges. They will continue to lift at first, eventually staying in place after you smooth them down. It's a laborious process for a beginner. But it works. 9) plug in your device or just leave it overnight to dry or "cure" (I turned my watch on, it was fine & then put it on the charger to cure) by the next morning the shield was dry & it looked perfect, no air bubbles or streaks. I barely put in any special effort, installed this while watching tv, while reclining on my chaise, in low light & it turned out flawlessly. But I've put stuff like this on before... It's been about 3-4 days and the shield is still looking good, I'll post pictures & the edges are all still wrapped to the screen nice and tight. If you want something that covers your watch screen rather than a small glass square that looks obvious, I urge you, TRY THIS PRODUCT OUT. It's easier to install than you think. Love this! **posted pictures...as you can see from the front view, the protector is invisible & crystal clear, the side view, the edges are covered, nice & tight, no lift at any edge. The feel is nice as well, smooth & your fingertips glide right over top like the actual glass of the watch. Great product!!!!

I received my screen shield on time, and ironically, I just got my Applewatch. The first installation went well, but a small piece of dust caused a minor imperfection which I ended up taking off and using the second shield provided. I have a need for perfection, especially when it comes to your beautiful Applewatch that you spent a lot of money on! I installed it that same day, and it turned out great! The only problem was after a day or 2, the 2 top corners started pealing off. I tried using the liquid to reapply, but it wouldn't work. I went a few days dealing with it until it started to collect dust, and I was about to buy a new set. I forgot though that they have a lifetime warranty, so instead of buying a new set, I contacted ArmorSuit for a new set! They were very understanding, and sent me out a new set promptly. I took the risk of taking off the old shield until my new set arrived, but I found that without a screen protector, I was constantly having to clear my screen of fingerprints! The military shield not only covers the whole screen of the Apple watch, but in my opinion, it also prevents finger prints. Sure sometimes they end up on the screen, but I wasn't needing to "clean it" as often. The screen is super smooth, and this time it adhered to all corners!! It does help letting it dry overnight as you won't bump it when it's still drying. My only advice is to install it in a clean environment!! I saw a tiny little hair from my dogs that ended up on the new shield somehow, but it was so minor I didn't want to rip it off and use the last shield. I did notice though that if you accidentally push your nail onto the screen, or bump it on an edge, sadly the shield takes the hit, and causes it to have a dent. All in all though, I can't complain because it really is made of a great quality material, it looks great (it's very smooth and you can barely tell you have a protector on it!), it covers the whole screen (unlike tempered glass, and other competitors), and they have a lifetime warranty! So if your looking for a great screen protector, I would recommend ArmorSuit!! The price is great, and if you use the 2 and need new ones due to mistakes or just wear and tear, their customer service is great! They communicate with you fast, and all you need to do is take a picture of the old shield showing the problem, or sending them in an envelope after you relieve the new ones! I am very happy with this brand, and I think everyone will too. Even if you make mistakes, remember they have a lifetime warranty!! And sure, it takes 5-7 business days to get to you, but it's worth it! You pay such a fantastic price to get the shields to begin with, and with them sending you new ones if need be, you can't beat it!! Thank you ArmorSuit!!

I watched the video in the instructions. A LOT of people mentioned it in their reviews. I did it and it helped tremendously. I got it stuck well the first, and second time. FINALLY, I got it right. Once you squeegee it down, you can't slide or center it. I applied it 3 times till I got it centered. It was wet and not stuck down yet.... let it set for 30 mins. Then took a warm blow drier and warmed it... let it sit... then pushed it down from the center with the supplied cloth.... then let it sit..., then warmed it with the blow drier... THEN began pushing down the edges to make it seal. I set this cover 3 times so far. The Spaigen rubber cover grabs the edges ( different product and not sold together). It lifts the screen protector. SO... I cut the edges down and attempting to get the edges from being grabbed. I went big this time with my recently repaired watch. REALLY , an amazing product and it is perfect now. This is my second Apple Watch. It is a replacement for the one I broke and now I am covering it as a new, untouched watch for a good start. The rubber case in the pics is for extra protection. So.... since I have a rugged rubber case and this film was being lifted at the edges... I removed and trimmed it further. When I put the film back onto the card o make the film smaller, I noticed an extreme color difference. This film has been on my watch maybe 2 weeks. It is brown now compared to the unused and newly trimmed film. I don't know why. Albeit, I am a car mechanic and oil may be involved. On the other hand, this watch is a new replacement watch and any time I need to shove my arm in a tight space, I have taken the watch off. Truthfully, I leave the watch home most days. So I don't know how the film yellowed.

perfect

Me gusto mucho. Cubre muy bien el reloj y dura mucho.

The best protection for your Apple Watch around. It may be expensive, but after trying the cheaper options... it's worth every penny.

Bon produit, bonne qualité.

Al parecer no es de la marca armor suit, pero funciona bien solamente se despegan un poco las orillas